You hand over a ring. A few minutes later, the buyer tells you it’s 14K and makes an offer. But what exactly did they just do? And how do you know the result is accurate?
Gold buyers use several methods to verify purity and weight. Not all methods are equal, and understanding the differences helps you spot a thorough buyer versus a sloppy one.
Testing Methods at a Glance
| Method | Speed | Accuracy | Destructive? | Common In |
| Magnet test | 2 seconds | Very low (screening only) | No | All shops |
| Acid test | 2 to 5 minutes | Good | Minor scratch | Most shops |
| Electronic tester | 30 seconds | Moderate | No | Mid range shops |
| XRF scanner | 30 to 60 seconds | Very high | No | Professional dealers |
| Specific gravity | 5 to 10 minutes | Good | No | Bullion dealers |
| Fire assay | Hours | Highest possible | Yes (sample destroyed) | Refineries only |
Most jewelry sellers will encounter the acid test, an electronic tester, or XRF. The method a buyer uses is one reason why gold buyers give different offers on the exact same piece.
Can You Test Gold at Home First?
You don’t need a lab. A few simple checks before your visit can save you a wasted trip.
The Magnet Check
Hold a strong magnet (neodymium works best) near your piece. Gold is not magnetic. If it sticks, it’s not solid gold. If it doesn’t stick, it could be gold but isn’t confirmed. Plenty of non gold metals like brass and copper are also non magnetic.
Check the Stamp
Look for karat markings like 10K, 14K, 18K, or 24K. If you see GP (gold plated) or GF (gold filled), the piece has very little actual gold inside. Learning to spot fake gold jewelry at home saves time and sets expectations.
Weigh It
Use a small digital scale accurate to 0.1 grams. Write down the weight. This gives you a reference number to compare against the buyer’s scale. If their reading is significantly different, you can ask why.
These home checks won’t tell you the exact karat. But they filter out the obvious fakes and give you a baseline before walking into any shop. More tips on preparing before you sell.
The Acid Test (Scratch Test)
This is the most common method in gold buying shops. It’s been used for centuries and it works.
How It Works
The buyer scratches your gold on a dark touchstone, leaving a small metal streak. Then they apply nitric acid to the streak.
- Streak dissolves → not gold at that karat level
- Streak stays → confirmed gold at or above that karat
Different acid solutions test different karats (10K, 14K, 18K, 22K). The buyer works from lowest to highest to pinpoint the exact range.
Pros and Cons
Pros: Cheap, fast, available in almost every shop. Reliable for standard karat testing.
Cons: Leaves a tiny scratch (usually invisible once polished). Can be fooled by thick gold plating over base metal. Not precise enough to distinguish between 13.8K and 14.2K.
The FTC’s Jewelry Guides require accurate karat representation on gold jewelry. The acid test is one of the accepted methods for verifying those claims.
XRF Analysis (X-Ray Fluorescence)
This is the gold standard for professional testing. If a buyer has one of these, you’re in good hands.
How It Works
The scanner shoots X-rays at your jewelry. The metals inside emit fluorescent X-rays back. The machine reads those emissions and calculates the exact composition, showing percentages of gold, silver, copper, and other metals on a screen.
Why It’s the Best
- Non-destructive. No scratching, no acid, no damage.
- Results in 30 to 60 seconds.
- Accurate to within 0.1% to 0.5% for gold content.
- Can detect plating layers that fool acid tests.
The Catch
XRF scanners cost $15,000 to $50,000+. Not every shop has one. Larger dealers and dedicated gold buyers are more likely to invest in this equipment. If a buyer uses XRF, it’s a sign they take testing seriously.
Understanding gold purity levels helps you read the XRF results and verify the buyer’s offer math yourself.
Electronic Gold Testers
These handheld devices are a step above acid testing but below XRF. You’ll see brands like Kee Gold Tester and GoldScreenSensor in mid range shops.
How It Works
The device sends a small electrical signal through the metal and measures conductivity. Different karats have different electrical signatures because of their unique alloy compositions. A karat reading appears on the screen.
Accuracy
Can distinguish between major karat levels (10K vs 14K vs 18K). Not precise enough for borderline readings. Accuracy drops with surface plating, dirt, or tarnish. The buyer should test on a clean, exposed area of the piece for best results.
Limitations
- Cheaper units (under $200) have wider error margins
- Thick plating can fool basic models
- Not reliable for very thin or very small pieces like thin gold jewelry
Most serious buyers use electronic testers as a screening tool alongside acid testing or XRF, not on their own.

Advanced Testing Methods
You won’t encounter these at a local gold buyer’s shop. But they’re worth knowing about because they’re what refineries and assay offices use.
Specific Gravity (Density Test)
The buyer weighs the piece normally, then weighs it again suspended in water. The difference reveals the item’s density. Pure gold has a specific gravity of 19.32, much heavier than most metals.
This method is completely non-destructive but doesn’t work well on jewelry with gemstones or hollow sections. More common for testing bullion than jewelry.
Fire Assay
A small sample is cut from the piece and melted at extreme temperatures with lead and chemicals. The process separates pure gold from everything else. Accurate to within 1 part per 10,000.
The LBMA requires fire assay for certifying Good Delivery gold bars. Destructive and expensive, so it’s a refinery tool, not a retail one.
Weighing: The Other Half of the Equation
Testing tells the buyer what karat your gold is. Weighing tells them how much gold is there. Both numbers go into the offer calculation.
What Buyers Use
Professional shops use digital precision scales accurate to 0.01 or 0.1 grams. These should be calibrated regularly to meet standards set by the National Institute of Standards and Technology (NIST).
The Pennyweight Trick
Some buyers weigh in pennyweight (dwt) instead of grams. This isn’t necessarily dishonest, but it can confuse sellers who don’t know the conversion.
1 pennyweight = 1.555 grams
If a buyer quotes weight in dwt and you only know grams, the numbers look smaller and the offer can seem reasonable when it’s actually low. Always ask for the weight in grams so you can verify against your home measurement.
What to Watch for as a Seller
Testing should happen in front of you. If a buyer takes your jewelry to a back room, that’s a red flag. Here’s what a transparent process looks like:
Green Flags
- Buyer tests and weighs in your line of sight
- Scale is zeroed before placing your item
- They explain the karat result and show you the reading
- They tell you the spot price they’re using and their payout percentage
- No rush, no pressure to accept immediately
Red Flags
- Testing happens out of sight
- Buyer won’t tell you the karat reading or weight
- Scale isn’t visible or isn’t zeroed properly
- They quote in pennyweight without explaining the conversion
- Offer seems significantly lower than what you estimated at home
- They pressure you to sell on the spot
If anything feels off, take your gold and leave. You can always visit another buyer. Knowing what gold buyers do with your jewelry after purchase also helps you understand their process and motivations.
Final Thoughts
Gold testing is chemistry, physics, and calibrated equipment. The more you understand about how buyers verify your gold, the harder it is for anyone to shortchange you. Ask what method they use. Watch the process.





